Kellsport Products stocks Eureka Fluid Film®  for same day shipment. Free shipping on Fluid Film® spray cans.

Product Data: #207

Effective January 2008

Fluid Film® NAS when combined with propellant in a pressurized aerosol can is designated Fluid Film® AS.

Fluid Film® AS & NAS are penetrants and lubricants also used for corrosion prevention. They are non-toxic, long lasting, thixotropic liquids that have been used for over fifty (50) years in the highly corrosive marine environment of ships and offshore drilling rigs. More recently they have been introduced and successfully utilized in the aerospace, aircraft and automobile industries as well as for home maintenance. Facilities where they are used include the following: government facilities, commercial fishing concerns, gas companies, agriculture, salt plants, municipal plants, power plants, manufacturing plants and pulp and paper mills.

Fluid Film® AS & NAS are formulated from specially processed wool-wax, highly refined petroleum oils and selected agents to provide corrosion control, penetration, metal wetting and water displacement. These long lasting products contain no solvents, will not dry out and will penetrate to the base of all metals, providing corrosion protection from both natural and industrial atmospheres. Heavily corroded and/or frozen parts such as nuts, bolts, shafts, etc. that would normally be damaged during maintenance, can be salvaged by applying Fluid Film® AS & NAS.

Details About Fluid Film®

National Stock Number

  

11 3/4 OZ, 12/CTN Aerosol Spray:  8030-01-387-1131 

12 oz, 12/CTN Non-Aerosol:   8030-01-381-6357  

1 gal, 4/CTN Non-Aerosol:   8030-01-386-3871    

5 gal Pail Non-Aerosol:   8030-01-387-1070  

 

Note: Environmentally Friendlier

AS (Less aerosol propellant) solvent free and non-toxic. NAS Solvent free and non-toxic. Container is reusable and recyclable.

Unless designated otherwise, the following data refers to Fluid Film® NAS or Fluid Film® AS after the propellant has evaporated away following spray application.

Appearance:  Clear, straw colored liquid.

Viscosity:   Brookfield

HBF, 70 ° F

  #2 Spindle

at 2 RPM

  2-4 reading

(3,200-6,400cps)

  

Flash Point, Bulk Liquid:

(ASTM-92)Cleveland Open Cup

   405°F minimum.

  

Non-Volatile:   89% minimum (3 hours @ 220°F).

V.O.C.:   Less than 1% 

  

Specific Conductivity:

Less than 10 -9 ohm/cm @ 1 mHz.

 

Specific Gravity:   0.875 - 0.885 (less propellant).

 

 

ASTM D-471 @ ± 158°F 70 hours

None on neoprene, buna-n and most synthetics. Some swelling on natural.  

  

Effect on Paint:   None on most painted surfaces.

  

Effect on Aluminum:   No pitting.

  

Extreme Pressure:

ASTM D-2782 Timken Method

   Fail load - 15 pounds.

  

Wear Prevention — Characteristics:

ASTM D-220 Four Ball Method

   40 Kg., 1200 RPM for 1 hour @ 167°F. Results: Scar diameter of 0.49mm.  

 

Repaintability:   Contain no silicones. It is recommended that surfaces treated with Fluid Film® AS or NAS be hot water or steam detergent washed (120°F), whichever is most effective.   

  

Corrosion Protection:

ASTM D-1735 Humidity Cabinet

   Passes 50 days.

   

ASTM D-1748:

Humidity Cabinet

   Passes 30 days. Corrosion Requirement (MIL-C-16173, Grade 3 -Soft Films), passes 5%. Salt Fog.

  

Water Replacement:   Displaces water from all metal surfaces (MIL-C-23411,Paragraph 3.6).  

  

Toxicity:   Non-toxic, LD-50 greater than 3 grams per kilogram. Non-irritating skin response. Very slight irritation to the eyes. (Toxicity tests performed according to standard methods by an independent laboratory).  

  

Warning:   AS: Extremely flammable. Contents under pressure. Do not puncture, incinerate or store above 120°F. Keep from open flame.

 

Spray Nozzle Cleaning:   Turn can upside down, point in a safe direction and spray until only propellant escapes. If spray button becomes clogged during use, pull it from the can and clean it with a fine wire or needle. Replace the button with a gentle twisting motion, keeping it pointed in a safe direction. Do not stick pins or other objects into nozzle tube.  

 

All nuts, bolts and studs.

Mechanical parts such as:

Brake levers.

Brake cable (emergency), speedometer cable.

Hood and trunk mechanismsd.

Door hinges, opening and locking mechanisms.

Window mechanisms.

Seat moving tracks and locks.

Tools.

Inside hub caps.

Wheel lugs.

Preservation inside doors.

Uncovered springs.

Battery post and connectors.

*Excellent vehicle undercoating corrosion preventative

(available in bulk) 3.79l, 20l, 208l.

Trailer attachments.

Truck bed bolts.

Blocks, turnbuckles.

Wire tie-downs.

Marine

Valves, stems, valve bonnets.

Port hole doggings and hinges.

Water tight door hinges and mechanism.

Elevator and dumb waiter guides.

Telegraph mechanism.

Furniture drawers and guide rails.

Signal light mechanism.

Chain falls, come-alongs, push and pull jacks.

Wire rope.

Machined surfaces, lathes, drills, shapers.

Nuts, bolts, studs, tools.

Exposed gear teeth.

Turnbuckles.

Clapper valve mechanism.

Piping and pipe joints.

Hatch doggings.

Throttle control mechanism.

Bright work (brass).

Winch brake mechanism.

Winch control mechanism.

Generator cooler heads.

Pelican hooks and turnbuckles, anchor chains.

Rudder machined surfaces.

Inside switch box doors.

Life boat falls.

Emergency steering blocks and sheaves.

Life line turnbuckles.

Forced draft blower mechanisms.

All blocks and sheaves.

Water tight deck drain enclosures.

All metal exposed to atmosphere or salt water spray.

Battery posts and connectors.

This document is subject to revision without notice.